{"created":"2023-06-20T15:05:23.732377+00:00","id":34694,"links":{},"metadata":{"_buckets":{"deposit":"13cf7a54-051d-4366-8d4a-d0543e543802"},"_deposit":{"created_by":1,"id":"34694","owners":[1],"pid":{"revision_id":0,"type":"depid","value":"34694"},"status":"published"},"_oai":{"id":"oai:jaxa.repo.nii.ac.jp:00034694","sets":["1887:1890","1896:1898:1899:1908"]},"author_link":["420233","420234","420235","420232"],"item_9_alternative_title_2":{"attribute_name":"その他のタイトル（英）","attribute_value_mlt":[{"subitem_alternative_title":"The Tensile, Compressive and Bending Tests of Mild Steel after Plastic Deformation by Simple Tension and Compression."}]},"item_9_biblio_info_10":{"attribute_name":"書誌情報","attribute_value_mlt":[{"bibliographicIssueDates":{"bibliographicIssueDate":"1954-03-08","bibliographicIssueDateType":"Issued"},"bibliographicIssueNumber":"6","bibliographicPageEnd":"244","bibliographicPageStart":"237","bibliographicVolumeNumber":"7","bibliographic_titles":[{"bibliographic_title":"東京大學理工學研究所報告"}]}]},"item_9_description_17":{"attribute_name":"抄録（英）","attribute_value_mlt":[{"subitem_description":"The tensile, compressive, bending and hardness tests are shown about specimens of usual carbon steel (0.22% C) after plastically deformed by statical tension and compression. The experimental results are as follows: (1) The proportional limit in the direction of pre-working is about 80-90% of the actual pre-working stress, but decreases about 30-50% of that in the opposite direction due to the Bauschinger effect. (2) On the bending test of the tensile pre-worked specimens, yielding starts at first on compression side of bending, and then the proportional limit on the compression side rises to about 2-3 times of the compressive proportional limit obtained after tensile pre-working. (3) Reversely to above mentioned, on the bending test of the compressive pre-worked specimens, yielding starts at first on tension side of bending, and then the tensile proportional limit rises to about 2 times of that obtained by tension test. (4) The difference of the proportional limits between tension and compression side of bending is about 10%, and this value is much smaller than that found in the case of the tension and the compression test of the pre-worked specimens. (5) The smaller the degree of pre-working is, the larger hysteresis loop for the first cycle of bending is obtained. Comressive residual strain is found after bending in total cross section of specimen pre-worked by tension, and tensile residual strain is found by compressive pre-working. (6) When the specimen is pre-worked up to about 10% strain, the hardness value does not rise for 5-10% strain in opposite direction to the pre-working, and shows work softening. (7) On the other hand, the work softening is not clear for smaller pre-working of about 3-5%, and the specimen shows work-hardening somewhat similar to that of virgin metal.","subitem_description_type":"Other"}]},"item_9_description_32":{"attribute_name":"資料番号","attribute_value_mlt":[{"subitem_description":"資料番号: SA2410176000","subitem_description_type":"Other"}]},"item_9_publisher_8":{"attribute_name":"出版者","attribute_value_mlt":[{"subitem_publisher":"東京大学理工学研究所"}]},"item_9_source_id_21":{"attribute_name":"ISSN","attribute_value_mlt":[{"subitem_source_identifier":"0371-6090","subitem_source_identifier_type":"ISSN"}]},"item_9_source_id_24":{"attribute_name":"書誌レコードID","attribute_value_mlt":[{"subitem_source_identifier":"AN00162611","subitem_source_identifier_type":"NCID"}]},"item_9_text_6":{"attribute_name":"著者所属","attribute_value_mlt":[{"subitem_text_value":"東京大学理工学研究所"},{"subitem_text_value":"保安大学校"}]},"item_9_text_7":{"attribute_name":"著者所属（英）","attribute_value_mlt":[{"subitem_text_language":"en","subitem_text_value":"THE INSTITUTE OF SCIENCE AND TECHNOLOGY, UNIVERSITY OF TOKYO"}]},"item_creator":{"attribute_name":"著者","attribute_type":"creator","attribute_value_mlt":[{"creatorNames":[{"creatorName":"福井, 伸二"}],"nameIdentifiers":[{}]},{"creatorNames":[{"creatorName":"佐藤, 四郎"}],"nameIdentifiers":[{}]},{"creatorNames":[{"creatorName":"FUKUI, SHINJI","creatorNameLang":"en"}],"nameIdentifiers":[{}]},{"creatorNames":[{"creatorName":"SATO, SHIRO","creatorNameLang":"en"}],"nameIdentifiers":[{}]}]},"item_files":{"attribute_name":"ファイル情報","attribute_type":"file","attribute_value_mlt":[{"accessrole":"open_date","date":[{"dateType":"Available","dateValue":"2020-01-24"}],"displaytype":"detail","filename":"SA2410176.pdf","filesize":[{"value":"621.0 kB"}],"format":"application/pdf","licensetype":"license_note","mimetype":"application/pdf","url":{"label":"SA2410176.pdf","url":"https://jaxa.repo.nii.ac.jp/record/34694/files/SA2410176.pdf"},"version_id":"3db778e6-a63d-4115-86e1-c6dee841877d"}]},"item_language":{"attribute_name":"言語","attribute_value_mlt":[{"subitem_language":"jpn"}]},"item_resource_type":{"attribute_name":"資源タイプ","attribute_value_mlt":[{"resourcetype":"departmental bulletin paper","resourceuri":"http://purl.org/coar/resource_type/c_6501"}]},"item_title":"単純引張或は圧縮加工材の引張,圧縮及び曲げについて","item_titles":{"attribute_name":"タイトル","attribute_value_mlt":[{"subitem_title":"単純引張或は圧縮加工材の引張,圧縮及び曲げについて"}]},"item_type_id":"9","owner":"1","path":["1890","1908"],"pubdate":{"attribute_name":"公開日","attribute_value":"2015-03-26"},"publish_date":"2015-03-26","publish_status":"0","recid":"34694","relation_version_is_last":true,"title":["単純引張或は圧縮加工材の引張,圧縮及び曲げについて"],"weko_creator_id":"1","weko_shared_id":-1},"updated":"2023-06-20T23:36:36.995498+00:00"}