| Item type |
テクニカルレポート / Technical Report(1) |
| 公開日 |
2015-03-26 |
| タイトル |
|
|
タイトル |
航技研ガン・タンネルにおける空力加熱測定法 |
| 言語 |
|
|
言語 |
jpn |
| 資源タイプ |
|
|
資源タイプ識別子 |
http://purl.org/coar/resource_type/c_18gh |
|
資源タイプ |
technical report |
| その他のタイトル（英） |
|
|
その他のタイトル |
INSTRUMENTATION TECHNIQUES FOR AERODYNAMIC HEATING MEASUREMENT IN N.A.L. HYPERSONIC GUN TUNNEL |
| 著者 |
井上, 安敏
山崎, 喬
INOUE, Yasutoshi
YAMAZAKI, Takashi
|
| 著者所属 |
|
|
|
航空宇宙技術研究所空気力学第一部 |
| 著者所属 |
|
|
|
航空宇宙技術研究所空気力学第一部 |
| 著者所属（英） |
|
|
|
en |
|
|
First Aerodynamics Division, National Aerospace Laboratory(NAL) |
| 著者所属（英） |
|
|
|
en |
|
|
First Aerodynamics Division, National Aerospace Laboratory(NAL) |
| 出版者 |
|
|
出版者 |
航空宇宙技術研究所 |
| 出版者（英） |
|
|
出版者 |
National Aerospace Laboratory(NAL) |
| 書誌情報 |
航空宇宙技術研究所報告
en : Technical Report of National Aerospace Laboratory TR-780
巻 780,
p. 35,
発行日 1983-09
|
| 抄録（英） |
|
|
内容記述タイプ |
Other |
|
内容記述 |
This report describes development and applications of instrumentation techniques for heat transfer measurements in the N.A.L. hypersonic gun tunnel since 1968. The measuring system, based on transient surface thermometry, mainly consists of a platinum thin-film gauge, constant current source and analog network, and enables one to measure the unsteady heating rate with a response time of less than 100μs. The details of fabrication techniques and performances of the system components are presented: Besides the thin-film gauge made by the sputtering method, a gauge made by the painting and baking method was developed for measurements under erosive circumstances of the gauge in the gun tunnel experiments. An R-C network, an electrical analog of the heat conduction into a slab, is used to obtain the instantaneous heating rate from the output of the thin-film gauge. The response times and outputs of analog networks were calculated by the Fourier expansion method when the input varied with time as the root t. It simulates the signal from the thin-film heated as a step functin. The output of the manufactured network was also calibrated by the above input signal. Both results for the manufactured analog network show that its response is fast enough and the difference of its output level from the solution of the heat conduction equation is less than 1%. The evaluations are made for errors caused by the system components during calibration and measurement. The analysis of non-onedimensional heat conduction effect, which is usually neglected in transient surface thermometry, shows that the effect is significant for the measurement of a heat flux distribution having a step peak such as observed in shock-interference heating. Some results of heat transfer measurements by this system are shown in the present paper. |
| ISSN |
|
|
収録物識別子タイプ |
ISSN |
|
収録物識別子 |
0389-4010 |
| 資料番号 |
|
|
内容記述タイプ |
Other |
|
内容記述 |
資料番号: NALTR0780000 |
| レポート番号 |
|
|
内容記述タイプ |
Other |
|
内容記述 |
レポート番号: NAL TR-780 |
naltr00780.pdf (4.7 MB)
